How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners must follow a set of specific steps to add an additional ignition key. This requires the use of a handheld computer, known as Tech-2, to be used by the dealer. Then a new car key and transponder must be purchased and programmed to the car.

Rotate your keys to prevent one from wearing out faster than another. This will also ensure that your keys remain in top condition.

Replacement Case

Unlike the classic Saab keys of old keys, the modern key fobs contain electronics that make it difficult to create a duplicate. That has made car theft significantly more difficult than it was a few years ago. It also makes it more costly to replace keys that were lost.

Every owner of a 9-3 saab 93 key fob should have at a minimum two functioning keys. It is costly to replace a lost or damaged key since it requires replacing the CIM module, as well as reconfiguring the locking cylinders. Dealers typically charge between $100 and $200 to do this.

There are ways to avoid the high cost. Some parts suppliers will use the code of an extra key to cut a new metal blade at a fraction what the dealer charges. The key must, however, be identical to the original one in order to function within your car.

You can also change the case yourself by following these steps. You will need to have a flathead and patience. With the screwdriver, slowly tear the plastic away and remove the emergency key from the case. Once the case is open take out all electronic components and place them into your new case. Put the correct key and badge into the case.

Replacement Battery

The Saab 9-3 replacement battery is a budget component that can be easily and quickly replaced. This YouTube tutorial for DIY Cyclone Cyd will show you how to replace the battery for Saab Replacement Key Programming the remote key fob in only four steps. This tutorial is suitable for any modern saab key fob, however the procedure might differ slightly.

This button is usually located close to the Saab logo on the back of the fob. This button is usually located on the back of your fob just below the Saab Logo. Use a flathead screwdriver to insert the screwdriver into the tiny hole on this button. This should be sufficient to let the fob case open so that you can change the battery.

Once the new CR1632 battery is installed You can then reassemble the remote key fob and program it to your car. The procedure should take no more than an hour at most. It is a very simple process that does not require any special equipment.

If you lose a key the procedure will be slightly more complicated, but it can still be done. The dealer must first read the VIN of the vehicle and then order a replacement TWICE module and key blade with the correct unique code. After that, they will be required to cut the replacement key and then program it using the latest software tool known as MDI.

Key Replacement Fob

The key fob is equipped with an internal battery that is used to lock and unlock your vehicle. The batteries last for a certain time and will eventually fail. This is a frequent issue that affects all cars. The good thing is that you can replace the battery in most key fobs, without having to replace the entire case. Amazon sells fobs for replacement that already have all the electronics in place. You can simply open the case and replace the batteries. It's important to note that you'll need to remove the emergency key first, and you can do this by putting an incredibly small screwdriver with a flat head into the slot in the middle of the case. Move the screwdriver around the case, and it will split open, saab Replacement key programming making it easier to remove.

When you are ready to replace your keys, make sure you have a spare since this will cut down the total cost by a significant amount. If you have a spare, you can ask the dealer to cut a new key and program it to the car, which is cheaper than replacing the whole key fob.

It is possible to add a second key to your vehicle in the event that you don't have one, but it will require lots of research and work. A second key can cost about a few hundred dollars and it requires programming of the car's computer. This can be done by a professional, but it's a costly option for the majority of owners.

Replacement Ignition

The latest Saab Replacement Key Programming 9-3 features an advanced alarm system built around a key code. If you lose your only key, it may be costly to get another one, as the car has to be equipped with a specific computer and also be programmed to accept a new key. Dealers can charge hundreds of dollars to program a new key if they are unable to complete the task.

If you've lost only one working key and a dealer is able to replace the computer in your car (known as the CIM or SAAB TWICE) to create a replacement, and they will charge top dollar for it. We can reprogram the current EEPROM in your car computer to be ready for an extra key. This will save you more than 50% on the cost you pay at a dealer.

If you've owned a SAAB 9-3 for an extended period of time you are aware that the ignition keys are not very durable. If your ignition key isn't functioning properly, it is time to look into replacing it. They can become sticky and the buttons can fall off. It's not as difficult as it seems to replace the ignition key. With the right tools, it is able to be done quickly.